1.7 Ft 1 to 3 OBD2 16 pin Splitter Extension Cable Male to Female Y J1962 Cable

#ad
#ad
Guangzhou Guoke e-commerce Co.,Ltd #ad - Length:1. 7 ft 50cm. 1x male and 3x female J1962 Ports. Can support three OBD device simultaneously without disturbing each other. 1 male splitter to 3 Female Extension, more convenient to use. We can according to the customer's requirement to produce different OBD cables, include length or different connector, welcome to contact with me to customize the more OBD cable.

More information about Guangzhou Guoke e-commerce Co.,Ltd #ad

Diageng Right Angle OBDII Y Splitter Cable 1'/30cm 1x Male and 2X Female J1962 Ports

#ad
#ad
Diageng MCS-OBD-EXT-RTE-SPT #ad - Diageng Right Angle OBDII Y Splitter Cable 1'/30cm 1x Male and 2X Female J1962 Ports #ad - Right angle primary connector- in an american/left hand drive vehicle this cable will push the "branches" "of the Y cable towards the center console/passenger side of the vehicle. 1 year Warranty. We took 2 of our most popular cables, the right angle extension and the Y splitter, and combined them to make a single high quality cable.

Unique Design. Flexible Shielded Wire. High quality over Mold J1962 Connectors.

More information about Diageng MCS-OBD-EXT-RTE-SPT #ad


Similar products


iKKEGOL OBD2 OBDII 1 to 3 Ultra Low Profile 16 Pin Male to Female Y Splitter Cord Diagnostic Extension Cable with Individually Power Switch 50cm / 20"

#ad
#ad
iKKEGOL 40127 #ad - Supports all standard OBD 2 protocols. With individually power switch, prevent battery damage. Ultra low profile design for hard to reach spots. Super flexible rubber coating is resistant to gas, oil, and most other common shop fluids. Supports all standard obd 2 protocols and 16-pin Pass-through for all OBD2 Vehicles.

50cm/20inch/1. 6ft length 1 male 16 pin j-1962 and 3 x female 16 pin J-1962 low profile extension connectors with Individually Power switch avoid battery drain and damage. Direct pass through on pins 2, 16, 14, 6, 15, 7, 4, 5, 10, Ideal for use with GPS trackers for the most discrete instalations. This obd2 splitter cable will allow you to split out one OBD II port into Three OBD II devices to the vehicle at the same time to save more room.

iKKEGOL OBD2 OBDII 1 to 3 Ultra Low Profile 16 Pin Male to Female Y Splitter Cord Diagnostic Extension Cable with Individually Power Switch 50cm / 20" #ad - Revolutionary flat flexible design allows to route the cable where you need it. Flexible Shielded Wire. 1 male splitter to 3 female, Can support three OBD device simultaneously without disturbing each other. High quality over Mold J1962 Connectors. 100% brand new and High-quality materials give the cable superior flexibility and durability.

. Description: head type: obd2 obdii / wire: 16 pin with switch Extension length: 50cm/20inch/1.

More information about iKKEGOL 40127 #ad


Similar products


Snap N Go Quick Hardwiring Kit Parking Mode Continuously Recording For BlackVue Dash Cameras Compatible DR-900S DR-750S DR-650S DR650GW DR490 DR590W DR590 DR450 DR430 DR500 DR500GW 1CH 2CH

#ad
#ad
7DAYCAM P1 #ad - Revolutionary flat flexible design allows to route the cable where you need it. In less than 5 minutes you are Be Able To Protect Your Car In Parking Mode. Easy to install and out of the way for a simple and elegant design. If you have any questions please feel free ask us. Snap on obd port and you are ready to go.

Right angle primary connector- in an american/left hand drive vehicle this cable will push the "branches" "of the Y cable towards the center console/passenger side of the vehicle. 1 year Warranty. Supports all standard obd 2 protocols and 16-pin Pass-through for all OBD2 Vehicles. 50cm/20inch/1. 6ft length 1 male 16 pin j-1962 and 3 x female 16 pin J-1962 low profile extension connectors with Individually Power switch avoid battery drain and damage.

Snap N Go Quick Hardwiring Kit Parking Mode Continuously Recording For BlackVue Dash Cameras Compatible DR-900S DR-750S DR-650S DR650GW DR490 DR590W DR590 DR450 DR430 DR500 DR500GW 1CH 2CH #ad - Direct pass through on pins 2, 6, 15, 4, 5, 16, 14, 10, 7, Ideal for use with GPS trackers for the most discrete instalations. This obd2 splitter cable will allow you to split out one OBD II port into Three OBD II devices to the vehicle at the same time to save more room. It can power your cam in normal mode or parking mode by simply plugging it into your OBD.

It will measure your batteries current voltage and shut off the camera if reaches the threshold. You can easily switch from two modes depend on your demand.

More information about 7DAYCAM P1 #ad


Similar products


ScanTool OBDLink SX USB: Professional Grade OBD-II Automotive Scan Tool for Windows – DIY Car and Truck Data and Diagnostics

#ad
#ad
ScanTool 425801 #ad - Display, graph, and log 90+ real-time parameters - life-like onscreen gauges to see more than what the manufacturer provides. Provide useful links to online database that provides trouble code descriptions and causes. Diy vehicle diagnostics: save time and money by reading and clearing 'check engine' and trouble codes yourself and determine problems before consulting a mechanic.

If you have any questions please feel free ask us. Revolutionary flat flexible design allows to route the cable where you need it. Powerful hardware and advanced, upgradeable firmware make SX the successor to the popular ElmScan 5 scan tool. At parking mode, the snap-n-Go will stop using battery power at 12V automatically to prevent battery grain.

ScanTool OBDLink SX USB: Professional Grade OBD-II Automotive Scan Tool for Windows – DIY Car and Truck Data and Diagnostics #ad - Control button to switch from normal ACC Mode and Parking Mode. Supports all standard obd 2 protocols and 16-pin Pass-through for all OBD2 Vehicles. 50cm/20inch/1. 6ft length 1 male 16 pin j-1962 and 3 x female 16 pin J-1962 low profile extension connectors with Individually Power switch avoid battery drain and damage.

Direct pass through on pins 2, 4, 6, 10, 15, 14, 16, 5, 7, Ideal for use with GPS trackers for the most discrete instalations. This obd2 splitter cable will allow you to split out one OBD II port into Three OBD II devices to the vehicle at the same time to save more room. It is fully obd-ii compliant, and connects with more cars than any scan tool on the market.

More information about ScanTool 425801 #ad


Similar products


AMP Research 79106-01A Override Switch PowerStep

#ad
#ad
AMP Research 79106-01A #ad - Free firmware and software upgrades: System includes a free license key for OBDwiz diagnostics software for easy to access graphs, logs and real-time engine data exports. Maximum vehicle coverage: works on more vehicles than any scan tool on the market including all 1996+ cars and light trucks sold in the USA except hybrid or electric vehicles.

. It will stop powering the BlackVue after 5 minutes when engine off at ACC mode. Works only with new type controller with 8-pin & 9-pin plug. Flexible Shielded Wire. Toggle switch can be easily installed on the dash and is wired directly to the PowerStep controller. Revolutionary flat flexible design allows to route the cable where you need it.

AMP Research 79106-01A Override Switch PowerStep #ad - Unique Design. Override switch allows you to manually deploy or retract your automatic steps regardless of what you do with the vehicles doors. Steps can be deployed for washing or loading vehicle and retracted safely out of the way when off-roading. Satisfaction guaranteed: your scantool is supplied with a 90-day money back guarantee if you are unsatisfied for any reason, along with a 3-year repair or replace manufacturer warranty.

Battery discharge prevention. High quality over Mold J1962 Connectors. At parking mode, the snap-n-Go will stop using battery power at 12V automatically to prevent battery grain.

More information about AMP Research 79106-01A #ad


Similar products


iKKEGOL 1.6ft Feet 50cm OBDII OBD2 16 Pin Right Angle Male to Female Y Splitter Extension Cable Car Diagnostic Extender Cord Adapter

#ad
#ad
iKKEGOL 40079 #ad - Revolutionary flat flexible design allows to route the cable where you need it. Main feature: the obd2 16pin extension cable allows you to connect compatible diagnostic tools with a 16 pin socket a right angle oBD-II Extension Cable that measures 19 inches long This can be used to plug into an OBD-II compliant vehicle and coupled with OBD-II diagnostic hardware On one end the male the adapter is at a right angle, the other two ends female is normal High-quality materials give the cable superior flexibility and durability Specification: OBD2 16Pin male to female extension cable.

Supports all standard obd 2 protocols and 16-pin Pass-through for all OBD2 Vehicles. 50cm/20inch/1. 6ft length 1 male 16 pin j-1962 and 3 x female 16 pin J-1962 low profile extension connectors with Individually Power switch avoid battery drain and damage. Direct pass through on pins 2, 6, 4, 16, 14, 10, 15, 5, 7, Ideal for use with GPS trackers for the most discrete instalations.

iKKEGOL 1.6ft Feet 50cm OBDII OBD2 16 Pin Right Angle Male to Female Y Splitter Extension Cable Car Diagnostic Extender Cord Adapter #ad - This obd2 splitter cable will allow you to split out one OBD II port into Three OBD II devices to the vehicle at the same time to save more room. Customized software and current control enable SNG to provide smooth and stable power for your BlackVue dashcam. At parking mode, the snap-n-Go will stop using battery power at 12V automatically to prevent battery grain.

Control button to switch from normal ACC Mode and Parking Mode.

More information about iKKEGOL 40079 #ad


Similar products


Diageng Ultra Low Profile Left or Right Angle OBDII Y Splitter Cable 30cm/12

#ad
#ad
Diageng Low Profile Y Cable #ad - In less than 5 minutes you are Be Able To Protect Your Car In Parking Mode. Override switch allows you to manually deploy or retract your automatic steps regardless of what you do with the vehicles doors. Steps can be deployed for washing or loading vehicle and retracted safely out of the way when off-roading.

Right angle primary connector- in an american/left hand drive vehicle this cable will push the "branches" "of the Y cable towards the center console/passenger side of the vehicle. 1 year Warranty. Supports all standard obd 2 protocols and 16-pin Pass-through for all OBD2 Vehicles. 50cm/20inch/1. 6ft length 1 male 16 pin j-1962 and 3 x female 16 pin J-1962 low profile extension connectors with Individually Power switch avoid battery drain and damage.

Direct pass through on pins 2, 15, 7, 5, 10, 16, 4, 6, 14, Ideal for use with GPS trackers for the most discrete instalations. This obd2 splitter cable will allow you to split out one OBD II port into Three OBD II devices to the vehicle at the same time to save more room. On one end the male the adapter is at a right angle, the other two ends female is normal.

Diageng Ultra Low Profile Left or Right Angle OBDII Y Splitter Cable 30cm/12 #ad - At parking mode, the snap-n-Go will stop using battery power at 12V automatically to prevent battery grain. Control button to switch from normal ACC Mode and Parking Mode. Free firmware and software upgrades: System includes a free license key for OBDwiz diagnostics software for easy to access graphs, logs and real-time engine data exports.

More information about Diageng Low Profile Y Cable #ad


Similar products


OLLGEN 3.3ft/1m OBD2 Cable Splitter,OBD-II 1 Male Splitter to 2 Female Extension Cable,Ultra Flat Low Profile Car Diagnostic Extender Cord Adapter,16 pin obd2 connector …

#ad
#ad
OLLGEN D0097 #ad - Supports all standard passenger vehicle OBD2 protocols. Professional grade scan tool: transform your Windows PC, laptop, or tablet into an accurate automotive diagnostic device not compatible with Apple iOS devices. Satisfaction guaranteed: your scantool is supplied with a 90-day money back guarantee if you are unsatisfied for any reason, along with a 3-year repair or replace manufacturer warranty.

You can easily switch from two modes depend on your demand. Maximum dashcam protection through micro controller chip. The current from obdii provide stable power for your dashcam than directly from battery. Description: this obd2 extension cable is 100% brand new and high quality, It can makes you more convenient to use OBD device.

At parking mode, the snap-n-Go will stop using battery power at 12V automatically to prevent battery grain. Control button to switch from normal ACC Mode and Parking Mode. This can be used to plug into an OBD-II compliant vehicle and coupled with OBD-II diagnostic hardware. Snap on obd port and you are ready to go.

OLLGEN 3.3ft/1m OBD2 Cable Splitter,OBD-II 1 Male Splitter to 2 Female Extension Cable,Ultra Flat Low Profile Car Diagnostic Extender Cord Adapter,16 pin obd2 connector … #ad - Free firmware and software upgrades: System includes a free license key for OBDwiz diagnostics software for easy to access graphs, logs and real-time engine data exports. Maximum vehicle coverage: works on more vehicles than any scan tool on the market including all 1996+ cars and light trucks sold in the USA except hybrid or electric vehicles.

Flexible Shielded Wire.

More information about OLLGEN D0097 #ad


Similar products


PRODIAG OBD2 OBDII 16pin Male to Female Extension Cable OBD II Diagnostic Extender 150cm 5ft16Pin OBD2 Cable

#ad
#ad
KAHE #ad - Can support two OBD device simultaneously without disturbing each other. 1 male 16 pin j-1962 and 2x female 16 pin J-1962. High-quality materials give the cable superior flexibility and durability. High quality over Mold J1962 Connectors. 1 male splitter to 2 female Cable, Compatible diagnostic tools with 16 pin socket.

Works only with new type controller with 8-pin & 9-pin plug. Ultra flat obd2 splitter low profile, easy to carry and use. High-quality materials give the cable superior flexibility and durability. Satisfaction guaranteed: your scantool is supplied with a 90-day money back guarantee if you are unsatisfied for any reason, along with a 3-year repair or replace manufacturer warranty.

PRODIAG OBD2 OBDII 16pin Male to Female Extension Cable OBD II Diagnostic Extender 150cm 5ft16Pin OBD2 Cable #ad - Professional grade scan tool: transform your Windows PC, laptop, or tablet into an accurate automotive diagnostic device not compatible with Apple iOS devices. Direct pass through on all 16 pins. Compatible diagnostic tools with a 16 pin socket. Ideal for use with GPS trackers for the most discrete instalations.

Right angle primary connector- in an american/left hand drive vehicle this cable will push the "branches" "of the Y cable towards the center console/passenger side of the vehicle. 1 year Warranty.

More information about KAHE #ad


Similar products


iKKEGOL Ultra Low Profile Left or Right Angle OBD2/OBDII Y Splitter Flat Ribbon Cable 1Feet/30cm -1x Male and 2x Female J1962 Ports

#ad
#ad
iKKEGOL 40054 #ad - High-quality materials bring the OBD2 cable superior flexibility and durability. Ideal for use with GPS trackers for the most discrete instalations. Use obd extension cable can save the wear and tear on your scan tool's OBD connector. If you have any questions please feel free ask us. 1 male 16 pin j-1962 and 2x female 16 pin J-1962.

10f length cable fit most of sedans, SUV and Pickups. High-quality materials give the cable superior flexibility and durability. Customized software and current control enable SNG to provide smooth and stable power for your BlackVue dashcam. Right angle primary connector- in an american/left hand drive vehicle this cable will push the "branches" "of the Y cable towards the center console/passenger side of the vehicle.

iKKEGOL Ultra Low Profile Left or Right Angle OBD2/OBDII Y Splitter Flat Ribbon Cable 1Feet/30cm -1x Male and 2x Female J1962 Ports #ad - 1 year Warranty. Multiple cables can be daisy-chained together to achieve longer length. Obd2 16pin male to female extension cable. Toggle switch can be easily installed on the dash and is wired directly to the PowerStep controller. High quality over Mold J1962 Connectors. Supports all standard obd 2 protocols and 16-pin Pass-through for all OBD2 Vehicles.

50cm/20inch/1.

More information about iKKEGOL 40054 #ad


Similar products